Products

Product Selector View our new products

All products below are listed alpha-numeric order. These listed products can be narrowed by using the search filters to the right. These filters cover the following areas:

  • Systems & Assemblies: will list only product allowed for the selected type of system or assembly
  • Product Category: Will only list products in the category chosen
  • Division: Will only list products are for use in that CSI division

Step 1: Select First Filter
Select the first filter to search by. If filter meets searching needs no further search action is needed.

 

Step 2: Select Second Filter (Optional)
If listed products need to be refined further, select another filter from the remaining two to further refine results.

 

Step 3: Select Last Filter (Optional)
If listed products need to be refined further, select final remaining filter to further refine results.

Search by:

Start over

Perma-Flex DPR Acrylic Finish

100% acrylic-based textured finish with dirt pick-up resistance (DPR): The surface of the finish hardens and does not soften again under heat. The non-tacky surface provides high resistance to accumulation of dirt, mold, and pollutants. Integrally colored with high-quality pigments. Exceeds ASTM and ICC Acceptance Criteria.  

 

Perma-Flex DPR Acrylic Finish is offered in six textures:

* Smooth * Coarse
* Fine * Swirl Fine
* Medium * MaxTex

 

Premium Stucco Finish

El Rey Premium Stucco Finish is an integrally colored portland cement based stucco finish, commonly called traditional stucco. It is available in 30 Standard colors and can be purchased as a pre-blended or base and color pack product.

Perma-Flex LASTIC Finish

100% acrylic-based elastomeric textured finish with dirt pick-up resistance (DPR): The surface of the finish hardens and does not soften again under heat. The non-tacky surface provides high resistance to accumulation of dirt, mold and pollutants. Highly flexible- can bridge preexisting or existing hairline cracks. Integrally colored with high quality pigments.

 

Perma-Flex LASTIC Finish is offered in six textures:

* Smooth * Coarse
* Fine * Swirl Fine
* Medium * MaxTex

 

Allegro II

Allegro II Cement Coating provides a cost-effective, durable and long-lasting colored coating that can be applied to portland cement surfaces such as: Stucco, Paint grade stucco, Concrete block/Concrete masonry unit (CMU) and Precast concrete.

Fog Kote

Fog Kote revives and enhances the color and natural beauty of cementitious stucco. Fog Kote improves color uniformity, enhancing the beauty of stucco. It becomes an integral part of the stucco surface as it is fade resistant and vapor permeable, will not chip or peel like conventional paint, restoring the color and beauty of stucco. Available in all 30 standard El Rey Premium Stucco colors. It is also convenient to use and apply because it mixes easily with water and can be applied to a wall with a standard portable pump/sprayer.

WallEase Basecoat

WallEase basecoat is a blend of cement, lime, aggregate, fibers and dry polymer. Benefits to using WallEase basecoat are it minimizes telegraphing of block wall (CMU) grout joints by evening the suction/absorption of blocks and mortar. It is to be used as a block wall (CMU) skim coat to level uneven surfaces. It allows for flexible application as it is a product that can be applied in multiple layers.

FastWall Concentrate

A factory controlled high-quality blend of portland cement, lime, fibers and proprietary additives that conforms to ASTM C926. ASTM C897 or ASTM C144 sand is added at the job site. Can be installed up to 1/2 in. (12.7mm) in one application.

FastWall Sanded

A factory controlled high-quality blend of portland cement, lime, fibers, proprietary additives and ASTM C144 sand that conforms to ASTM C926. Factory-blended mix that requires only the addition of water. Can be installed up to 1/2 in. (12.7mm) in one application.

Fiber-47 Concentrate

Factory blend of portland cement, lime, fibers, and proprietary additives designed for scratch and brown coats for stucco assemblies complying with ASTM C 926. Fiber-47 can be applied over properly prepared masonry and concrete substrates, and code-conforming lath assemblies. Can be finished with integrally colored El Rey Premium Stucco or Perma-Flex Acrylic Stucco Finish.

Fiber-47 Sanded

Factory blend of portland cement, lime, fibers, and proprietary additives designed for scratch and brown coats for stucco assemblies complying with ASTM C 926. Fiber-47 can be applied over properly prepared masonry and concrete substrates, and code-conforming lath assemblies. Can be finished with integrally colored El Rey Premium Stucco or Perma-Flex Acrylic Stucco Finish.

Parex USA Masonry Veneer EPS Basecoat and Adhesive

EPS Basecoat & Adhesive is the first premium grade basecoat used to adhere and coat EPS continuous insulation sheeting as part of the Parex USA MVS - CI System. This specialized EPS Basecoat creates an energy efficient wall substrate suitable for the application of manufactured masonry veneers or in conjunction with other Parex USA finishes.

Insul-Bond P (Pre-blended)

A base Coat for El Rey EIFS. Adhesive to laminate EPS to listed substrates. Applied without the addition of cement. Mixed on site with water. Excellent workability.

Parex USA Stucco Level Coat

Stucco Level Coat is a surface leveler and mesh adhesive for use in Parex USA Krak-Shield assemblies. Bonds to stucco brown coat. Can be applied in a thin layer. Applied without the addition of cement. Mixed on site with water only. Excellent workability.

Parex USA Stucco Mesh

4.5 oz fiberglass 38 in. (96.5 cm) mesh. For increased crack reduction and strength. Embed in Stucco Level Coat to smooth and level surface for finish. Use with Krak-Shield and Krak-Master stucco assemblies. Not for use on EIFS

Parex USA Sandable Basecoat

A 100% Acrylic sandable basecoat that comes as a gray base. It enhances the appearance and uniformity of smooth finishes. It can be easily recoated with Parex USA Allegro II. Ideal over EIFS basecoats, stucco basecoats, stucco finishes, and interior drywall.

Parex USA DPR Coating

A 100% acrylic-based non-textured coating. DPR (Dirt Pick-up Resistance): The non-tacky surface provides high resistance to accumulation of dirt, mold, and pollutants. Excellent hiding power as well as flexibility and drying characteristics. The surface of the coating hardens and does not soften under heat. Integrally colored with high quality pigments.

Parex USA Elastomeric Coating

A 100% acrylic Elastomeric non-textured coating. Highly flexible: can bridge existing hairline cracks. DPR (Dirt Pick-up Resistance): The non-tacky surface provides high resistance to accumulation of dirt, mold, and pollutants. It provides excellent hiding power as well as flexibility and drying characteristics. The surface of the coating hardens and does not soften under heat. Integrally colored with high quality pigments.

Parex USA Primer

A 100% acrylic-based primer. Reduces the chance of efflorescence which may result from the cement content of various bases. Enhances the appearance and uniformity of the finish. Water-vapor permeable. Does not create a vapor retarder. Improves finish coverage.

Parex USA PrimeShield

Is a 100 percent acrylic-based primer that improves the mechanical bond of the finish to the stucco substrate. PrimeShield reduces the chance of efflorescence which may result from the cement content of various bases. It also enhances the appearance and uniformity of the finish. The product is water-vapor permeable and does not create a vapor retarder.

Parex USA Adacryl Acrylic Admix & Bonder (formerly Superior Additive 200)

100% acrylic emulsion designed for use with for portland cement based products. High-performance acrylic polymer bonding agent. Admixture in portland cement based mixes.

Parex USA Metallic Coating

100% acrylic based metallic coating that provides a glossy, metallic appearance.   Economically replicate the look of metal panels with the ease of a coating application. Includes dirt pickup resistance (DPR) which ensures the coating does not soften under head and resists accumulation of dirt, mold, and pollutants.  Available in 12 standard colors and unlimited custom colors.

Parex USA 352 Adhesive

4.5 oz fiberglass mesh 19 in (48.2 cm) wide mesh. Self-adhesive, facilitates the wrapping of complex contours. Is alkali-resistant. NOTE: Complex architectural details only, not for use on full walls.

Parex USA 355 Standard Mesh

4.5 oz fiberglass 38 in. (96.5 cm) wide mesh. Is highly flexible for full walls or details. Is alkali-resistant. Standard reinforcement of Parex USA EIFS walls for impact resistance and details. Required in combination with 358.14 High Impact Mesh or 358.20 Ultra High Impact Mesh. May be used in Parex USA Krak-Shield assemblies.

Parex USA 356 Short Detail Mesh

4.5 oz fiberglass 9.5 in. (24 cm) wide mesh. Is highly flexible for use on details. is alkali-resistant. Ideal for use in back wrapping, corners, reveals and trim. May be used in combination with 355, 358.6 & 358.10 meshes in Parex USA Krak-Shield assemblies.

Parex USA 358.10 Intermediate Impact Mesh

12 oz fiberglass 38 in. (96.5 cm) wide mesh. Is an intermediate strength mesh used to enhance impact and abuse resistance. Is alkali-resistant. Use with Parex USA EIFS to achieve EIMA's medium impact strength classification. Can be used in combination with 355 Standard Mesh and 356 Short Detail Mesh. May be used in Parex USA Krak-Shield assembly.

Parex USA 358.14 High Impact Mesh

15 oz fiberglass 38 in. (96.5 cm) wide mesh. A high strength mesh used to enhance impact and abuse resistance. Is alkali resistant. Use with Parex USA EIFS to achieve EIMA's high-impact strength classification. 355 Standard Mesh is required in combination with 358.14 High Impact Mesh.

Parex USA 358.6 - 6 oz Mesh

6 oz fiberglass 38 in. (96.5 cm) wide mesh. Is the next level strength mesh used to enhance impact and abuse resistance. Is alkali Resistant. Can be used in combination with 355 Standard Mesh, 356 Short Detail Mesh, 358.14 High Impact Mesh or 358.20 Ultra High Impact Mesh. May be used in Parex USA Krak-Shield assembly.

Parex USA Carvable Mortar

Parex USA Carvable Mortar is a polymer modified architectural mortar used to create shapes and sculpted structures. It is the ideal product to mimic the look of wood, rock or stones.


Parex USA Carvable Mortar can be build up to 6” in total thickness and can be used over a wide variety of substrates. It can be machine or hand applied and is paintable

Parex USA 360 Fast Window Mesh

A preformed mesh used to reinforce the corners of rough openings. It is ready to use and pre-cut for fast installation It should be used in conjunction with Parex USA Weather Tech WRBs: WeatherSeal Spray & Roll-On, WeatherSeal Trowel-On and WeatherBlock SP1 Spray & Roll-On.

Parex USA 360 Fast Windown Mesh comes in boxes of 40 units.

Parex USA 600 Clear Sealer

A 100% acrylic transparent coating. Contains EPA-registered mildewcide and algicide. Dirt resistant. The coating hardens and does not soften under solar heating. The nontacky surface provides high resistance to accumulation of dirt and pollutants. Water vapor permeable.

Parex USA 610 Matte Clear Sealer

A 100% acrylic transparent coating. Developed with a special matte agent to reduce sheen.Contains EPA-registered mildewcide and algicide. Dirt resistant. The coating hardens and does not soften under solar heating. The nontacky surface provides high resistance to accumulation of dirt and pollutants. Water vapor permeable.

Parex USA Pro-Tect (formerly Crown Seal)

Pro-Tect is a clear water repellant used to protect stucco, masonry and mature concrete from water, enhancing the beauty of cementitious stucco, masonry and mature concrete by improving stain resistance. Pro-Tect maintains the beauty of stucco by reducing susceptibility to freeze-thaw damage, efflorescence, biological growth. Available in both one and five gallons.

Parex USA Accel-Dry

Accel-Dry is an acrylic and elastomeric finish accelerator. Accel-Dry admix is ideal for wet and cold climates as it allows finishes to dry quicker. This is a key feature for jobs that might face inclement weather or need to be completed quickly.

Parex USA Accel-Pak-Rapid Set Admix

Rapid set admix for any Parex USA polymer modified EIFS Base Coat & Adhesive to reduce set time for Winter weather or quick EIFS patch & repair work.

Parex USA Quik Cure

Water-based acrylic curing membrane formulated to provide excellent performance in the water retention section of ASTM C 309. Provides a curing membrane over cementitious surfaces allowing acrylic finishes to be applied quickly, while protecting against delamination and efflorescence. Provides a sound, sealed substrate for a uniform finish over either stucco or concrete.

WeatherTech WeatherFlash

WeatherFlash liquid flashing and joint filler is used to prepare and seal exterior wall rough openings and detail joints as part of the WeatherTech air and water

barrier system.

Areas of Use

• Window and door rough openings

• Sheathing joints

• Fastener points

• Wall penetrations (Beams, pipes, utility

boxes, etc.

 

Available in 20 oz Sausage Packs or 3 Gal Pails

WeatherBlock SP1 Spray & Roll-On

A Class I 100% Acrylic co-polymer fast drying vapor barrier, elastomeric waterproof and air barrier coating which can be either rolled, brushed, or spray applied. Is designed for use as vapor barrier behind exterior claddings. Is extremely flexible: can bridge cracks and accommodate small movements up to 1/32 in. (0.8mm). Bridges 1/8 in. (3mm) gaps at sheathing board joints with Parex USA 396 Sheathing Tape embedded.

WeatherDry

An acrylic co-polymer based, waterproofing base coat. For use with acrylic and elastomeric finishes. Requires the addition of portland cement.

 

VIDEO: View the Parex USA Weatherseal Spray and Roll-On / Trowel-On Video

WeatherSeal BG

A Single-component, non-fibrated, asphalt modified, neoprene waterproofing membrane which can be either troweled, rolled, brushed, or spray applied. Designed to provide high-performance below grade protection from positive side water pressure. Allows low levels of moisture vapor to escape to prevent blistering and delamination of the applied membrane while prohibiting infiltration of moisture through foundation walls, footings, retaining walls, planter boxes and between slab. Solvent free formulation incorporate anti-microbial additive to prevent mold and mildew growth.

 

VIDEO: View the Parex USA Weatherseal Spray and Roll-On / Trowel-On Video

WeatherSeal SB

A single component cement base waterproofing coating for CMU and concrete. It is a multipurpose polymer modified waterproofing product: Air Barrier, Water Resistive Barrier, and Scratch Coat that can be used above grade and below grade for planters or concrete foundations.

Parex USA WeatherSeal SB is can be used to fill joints in CMU and to level rough concrete or CMU walls.

WeatherSeal Spray & Roll-On

A 100% acrylic elastomeric waterproof membrane and air barrier which can be either rolled, brushed, or spray applied. Extremely flexible: can bridge cracks and accommodate small movements up to 1/32 in. (.8mm). Designed for use as water-resistive barrier behind El Rey EIFS or stucco. Bridges 1/4 in. (6 mm) gaps at sheathing board joints with 396 Sheathing Tape embedded.

 

VIDEO: View the Parex USA Weatherseal Spray and Roll-On / Trowel-On Video

WeatherSeal Trowel-On

A 100% acrylic based, trowelable water-resistive barrier membrane. Designed for use as water-resistive barrier behind exterior claddings. Extremely flexible: can bridge existing hairline cracks and accommodate small movements.

 

VIDEO: View the Parex USA Weatherseal Spray and Roll-On / Trowel-On Video

Parex USA 365 Flashing Membrane

Parex USA 365 Flashing Membrane is a self-sealing rubberized asphalt membrane that functions as a moisture and air barrier. It is 30 mils (0.75 mm) thick and black in color. It can be applied to various substrates such as wood, metal, gypsum sheathing and to house wrap and other weather resistive barriers. The Parex USA 365 Flashing Membrane is unique: it is faced with a non-woven, integrally bonded fabric that enables adhesion of Parex adhesives. It functions as a seal and flashing at sills of rough openings, deck framing, etc., interfacing with the building substrate and other weather resistive barriers.

 

Our Flashing Membrane is offered in the following dimensions:

* 6" x 100'

 

Parex USA 369 DrainEdge

Speeds and simplifies application of the WaterMaster systems and assemblies. Eliminates need for pre-wrapping or rasping the back of boards at terminations. Eliminates the need for mineral wool and track at terminations.

Parex USA 396 Sheathing Tape

Non-woven fabric used to tape the joints of the sheathing boards to which a Parex liquid water-resistive barrier is applied.

 

Our Sheathing Tape is offered in 3 sizes:

* 4" x 500'

* 6" x 500'

* 9" x 500'

Perma-Flex 400

Perma-Flex 400 is an environmentally friendly,non-toxic, 100% acrylic,water-based masonry surface conditioner. It improves adhesion of Perma-Flex acrylic stucco products to cementitious substrates as well as improves workability of trowel applied Perma-Flex Acrylic Stucco Finishes.